DJI T70P Water Cooled Mist Sprinklers

£450.00

Water-cooled ultra-fine mist system
Optimised for DJI Agras T70P
Improves canopy penetration and coverage
Designed for orchard and specialty crops
Enhanced cooling for sustained performance

Category: DJI Agras T70

DJI Agras T70P Water-Cooled Centrifugal Mist Sprinklers

The DJI Agras T70P Water-Cooled Mist Sprinklers represent the pinnacle of high-capacity, thermally managed chemical delivery systems designed exclusively for the Agras T70P platform. Engineered to thrive during intensive, back-to-back industrial spraying operations, this system integrates an innovative fluid thermal-exchange path directly into the sprinkler matrix. By utilizing the active payload flow to continuously absorb and bleed off heat from the high-RPM centrifugal motors, the water-cooled architecture prevents thermal degradation, allowing the system to sustain extreme flow rates without safety cutoffs.

Agras T70P Native Fit
Integrated Liquid-Cooling Duct
Ultra-Fine Centrifugal Mist
Controllable Micron Spectrum
Drip-Free Solenoid Valves

DJI Agras T70P water-cooled centrifugal mist sprinkler system installation

Continuous Dual-Atomization Under Extreme Loads

Standard atomizing hardware can struggle with core heat accumulation when subjected to massive electrical draws over long summer field days. The T70P water-cooled design natively solves this limitation, transforming your liquid payload into an active heat sink for the entire spraying assembly.

High-speed centrifugal disks spin smoothly to shred liquid mixtures into precise, micron-optimized particles.
Dual-channel electromagnetic flow meters provide real-time volume analysis to completely eliminate under-sprayed stripes.
Industrial-grade seals protect the high-torque inner motor components against corrosive agricultural chemicals and fine spray back-mists.

Dynamic Penetration for Demanding Canopies

Whether target lines dictate vast open field rows or densely tangled orchard crops, the water-cooled centrifugal system modifies its particle distribution patterns on the fly.

Variable Atomization Profile: Gives field crews full control over droplet size boundaries to strike the perfect balance between drift reduction and canopy coverage.
Instant Solenoid Brake: Snaps shut the instant the aircraft finishes a swath line, saving chemical volume and stopping chemical burning on borders.
Optimized Downwash Shrouding: Factory guards redirect the escaping mist directly into the propeller downwash profile for maximum underside leaf contact.

Close up view of the water-cooled centrifugal motor housing and misting disc assembly

Thermal & Misting Efficiency

Fluid Heat Exchange

Active Water-Cooling Path

Circulates chemical fluid around the active electronics, extending motor duty life during maximum flow operations.

Droplet Atomization

Centrifugal Mist Control

Fling-disc technology eliminates narrow pressure nozzles, meaning zero clogs from thick formulas.

Technical Specifications

System Hardware Profile
Sprinkler Architecture	Dual-Atomization Water-Cooled Centrifugal Mist Sprinkler
Thermal Management	Integrated fluid-jacket heat exchange (liquid payload cooling)
Valving Core	High-speed anti-drip solenoid actuation valves
Flow Verification	Dual-channel non-contact electromagnetic flow meter
Material Composition	Chemical-resistant, UV-stabilized industrial polymers and alloys
Platform Compatibility	DJI Agras T70P & Agras T100 platforms exclusively

Maintain precise, lock-step delivery and prevent thermal field issues. Contact the Drone Sales UK commercial team today for genuine replacement parts, nozzle upgrade arrays, and seasonal team packages.

Enquire About T70P Misting Hardware

How does the water-cooling system on these sprinklers work?›

The mist assembly features an integrated liquid-cooling thermal jacket surrounding the internal electric motor. As the spray liquid or water flows from the 70-litre tank to the nozzles, it passes through this cooling jacket first, continuously absorbing heat from the high-rpm motor. This ensures the system runs perfectly cool even when operating at maximum output during hot summer days.

What makes a “Mist” sprinkler different from standard centrifugal setups?›

While standard centrifugal sprinklers focus on a broad droplet range for universal fields, the mist variant is optimized for ultra-fine micro-droplets (typically 30 to 120 micromitres). This creates a floating, fog-like mist cloud that slowly drifts through dense branches, coating both the tops and bottoms of leaves in complex orchard canopies rather than falling straight to the ground.

What are the primary use cases for the T70P mist sprinkler array?›

These units are highly valued for orchard foliar feeding, delicate greenhouse treatments, and frost prevention operations. During freezing spring nights, running pure water through the mist sprinklers creates an insulating layer of condensation over delicate buds, protecting high-value fruit crops from severe frost damage.

Can these mist sprinklers cause clogging issues with thicker chemicals?›

Because misting relies on tighter tolerances to generate microscopic droplets, it requires highly filtered liquid. Thick wettable powders or heavily viscous mixtures can increase wear. It is highly recommended to use clean liquid solutions or ensure all mixtures are completely dissolved and run through fine-mesh inline filters prior to filling the tank.

Are these sprinklers standard or an optional add-on for the T70P?›

The water-cooled mist sprinklers are an optional enterprise upgrade module for the standard Agras T70P airframe. They can easily replace the factory centrifugal sprayers via the modular boom mounts when your farm rotation shifts from broadacre arable crops to technical orchard or vineyard canopy management.

What daily maintenance do water-cooled mist systems require?›

Critical Post-Flight Steps: Because the liquid channels act as the motor cooling system, mineral scaling or chemical crystallisation inside the cooling paths can completely block flow and overheat the motor. Always flush the array with warm, clean water or a neutralising cleaning solution for 3 to 5 minutes after every shift to keep the lines completely clear.

Does Drone Sales UK provide installation support for this mist system?›

Yes. Drone Sales UK provides complete setup, fitting, and calibration support for the T70P mist upgrade. We ensure the new fluid plumbing lines and electronic cooling protocols match your Agras system software, and we stock spare nozzle tips, cooling jackets, and inline filters to keep you running flawlessly.

DJI AGRAS T70P Water-Cooled Mist Sprinkler Set · 4-Sprinkler Optional Upgrade · Max 40 L/min Orchard Flow Rate · Dual-Centrifugal Atomization · Micro-Droplet Precision (Down to 50 μm) · Self-Cooling Liquid Flow Path · 65% Increase in Canopy Penetration · Dual-Channel Electromagnetic Flow Meter

DJI AGRAS T70P Water-Cooled Mist Sprinklers — Key Specifications

An elite-tier specialized fluid application system designed for high-density orchard canopy penetration and micro-droplet misting. These advanced sprinklers utilize an integrated liquid-jacketed water-cooling profile to safely regulate motorized spinning assembly temperatures during high-volume, continuous crop misting operations.

Liquid-Jacketed Water Cooling
LX09550SX Premium Mist Model
Ultra-Fine 50 – 150 μm Atomization
Up to 40 L/min Peak Fluid Feed
Extended High-Load Thermal Runway
4 – 11 m Adaptive Swath Width

Thermal Regulation & Mechanical Profiles

Hardware Designation: LX09550SX (Optional Specialized Water-Cooled Mist Nozzle Assembly).
Active Water Cooling: Diverts a portion of the incoming chemical or water payload through internal thermal heat-sink jackets surrounding the high-RPM sprinkler motor core, dissipating heat during extended continuous mist operations.
Thermal Longevity: Prevents motor degradation, brush electrical failure, and housing warping when operating at max rotational limits in blistering field environments up to 40 °C.
Deployment Configuration: Installs directly onto the fixed 1874 mm rear nozzle mounts, supporting standard dual arrays or full quad-sprinkler payload expansions.

Mist Generation & Flow Dynamics

Ultra-Fine Atomization: Specifically optimized to operate on the tightest band of the droplet scale, squeezing fluid out at 50 μm to 150 μm for unparalleled under-leaf canopy adhesion and foliage coating.
Pressure Capability: Orchestrated to handle systemic delivery pump flow rates of up to 30 L/min (Standard 2 sprays) and up to 40 L/min (Optional 4 sprays) without backing up pressure loops.
Effective Swath Width: Produces a highly uniform, dense cloud expanding across an active 4 to 11-meter operational width.
Blockage-Free Internal Paths: Maintains a wide-mouth internal intake fluid route, allowing thick orchard chemicals or sulfur suspensions to pass cleanly without clogging narrow orifices.

* Ultra-fine misting configurations below 150 μm are highly susceptible to wind drift and evaporation. Exercise caution when flying at speeds near the safe obstacle avoidance ceiling of 13.8 m/s or in wind thresholds nearing 6 m/s. Ensure a thorough fresh-water purge cycle is completed immediately following chemical applications to avoid concentrated crystallization within the water-cooling channels.